The N2CID Digital Amateur Radio Repeater Network has XLX Reflector clusters for ham use. The reflectors currently have multi-mode trans-coding enabled, meaning it can be accessed via Icom G3 Terminal Mode, D-Star, DMR and System Fusion (Wires-X) where all modes can talk together. The idea of the reflector is to be a single place for all local repeaters, hot-spots and remote users/sites to connect and stay in contact with friends and family no matter the digital mode. All HAM’s are welcome to use the system. Here are the multiple ways to connect remotely:
- DMR: Brandmeister Talk Group 310441
- D-Star: XRF891C, DCS891C, REF891C
- Pi-Star: ‘XLX Master:’ XLX_891 C
- Yaesu Fusion: Reflector 48010 (7 wires-x rooms available currently)
- Icom G3 Terminal Mode (RS-MS3A Android app)
- DO NOT QUICK KEY. Wait about 2 seconds between transmissions when talking between modes.
- Quick keying can lead to your mode not being picked up by the other modes.
- Allow an even longer time during round table discussions when crossing modes.
- Announce what mode you are coming in on.
- For example: “This is N2CID on DMR, monitoring”
- OR “N2CID this is KB2FMD on D-Star”
- Don’t be afraid to say hello to unfamiliar voices/call-signs.
How to connect to the N2CID Network using “DMR Gateway” in Pi-star: (Recommended Way to connect!)
“DMR Gateway” offers the ability to connect to the N2CID Network from your repeater or hot-spot as opposed to using Brandmeister or anyone else. Your connection will be direct to the master N2CID DMR cluster, bypassing Brandmeister or any other third party all together. If Brandmeister ever has problems you can always connect directly to us. The below method will route the N2CID TG 310441 direct to us and everything else will go to BrandMeister.
- On the configuration page, under “DMR Configuration” change “DMR Master” to “DMRGateway”.
- Set BrandMeister master to BM_United_States_3101.
- Make sure that “BrandMeister Network Enable:” is enabled.
- Change “XLX Master” to “XLX_891”. You can opt to disable DMR+ Network to disable the additional voice traffic.
- Choose “C” for the startup module.
- Enable “XLX Master Enable“
- Apply Changes
- Go to Configuration, Expert, then DMR GW, then under the “XLX Network” section change TG: 6 to TG: 310441 Apply changes and your done!
Connecting to our Yaesu Fusion Wires-X Rooms
We should be in the reflector registry as YSF Reflector 48010 but if not you can also add our system to your hosts file in most cases (pi-star: /usr/local/etc/YSFHosts.txt) Your entry should look like this…
The default wires-x room you will be placed in is “C” which is our group room. You can also use Wires-X and select other rooms.
Once added just restart your pi-star and select from the drop downs.
There is no need to register your call-sign on D-Star to use this reflector like you would to access REF reflectors. XLX reflectors work without checking a trust server. So do not worry if you are a D-Star user and have never gone through a call-sign registration process. You can still use this reflector!
The reflector has a real-time web dashboard to see other nodes and users connected and to what modules or rooms they are connected to.
How to connect to the reflector on your D-Star Radio:
Because the advanced XLX protocol is not available in DR mode radios, like REF, you will have to use the “UR” field to link manually. Trans-coding occurs on the C module of the reflector and will need to be connected through a hot-spot or pi-star enabled repeater. Icom based gateways do not support connecting to XLX reflectors. For example: G1, G2, G3
- Kerchunk XRF891CL in the UR field while connected to a hot-spot or repeater.
- Switch to “Use Reflector” in DR mode radio and start talking.
- Optionally you can use the traditional method on the radio and use REF891C
How to connect to the reflector on your DMR Radio using Brandmeister:
On any Brandmeister connected node/repeater simply use Talk Group: 310441
!! There are occasions when Brandmeister is doing maintenance or work on their end, and will drop the peers. Talkgroup 310441 will remain active locally as we are not dependent on BM. In which case, you can use the “DMR Gateway” method below to bypass BM and connect direct to our system. !!
How to connect via DMR directly using the OpenSpot:
You can connect to this reflector directly from the SharkRF OpenSpot as oppose to using Brandmeister. Your connection will be direct to the reflector, bypassing Brandmeister all together. If Brandmeister ever has problems, you can still connect via DMR. The dis-advantage is as you will see, its a little more tricky to connect.
In the OpenSpot
- Set the Modem to DMR (for crossmode)
- Go to the “Connectors” Tab:
- Edit Connector: “HomeBrew/MMDVM“
- Then under “DMR/HOMEBREW/MMDVM“
- Choose “Protocol“: MMDVM
- Choose “Server“: XLX891
In your DMR Codeplug
You will create at least 3 new contacts and a few channels
- Create the following contacts:
- Name: “TG 9” TG: 9 (Group Call)
- Name: “OPS XLX Disconnect” TG: 4000 (Group Call)
- Name: “OPS XLX C” TG: 4001 (Private call)
- Program these contacts into channels for the OpenSpot. TG 9 is where link announcements are made along with how you TX/RX on the reflector. Create a channel for TG 9, a channel for XLX C, a channel for XLX Disconnect, etc… then add them into a zone.
On Your DMR Radio
- Go to the zone where you programmed the channels for your OpenSpot.
- The C Module is where trans-coding occurs. Kerchunk your channel “OPS XLX C” and immediately switch to “TG 9”. You can create a RX Group for the “OPS XLX C” channel if you want to avoid switching channels rapidly to hear the announcements.
- In order to talk on and listen to the reflector make sure to select your channel “TG 9”.
- To switch modules, you must disconnect first, then link to the module of your choice. Simply switch to “OPS XLX Disconnect” and kerchunk to send a disconnect.
Icom G3 Terminal Mode:
Gateway Repeater: xlx891.wnydmr.network
Terminal AP Callsign: YOURCALL <space> identifier (ie: KB2XYZ B) (shorter callsigns require 2 spaces!)
Gateway Type: Global
UDP Hole Punch: ON
Allowed Callsign: Disable